Skip to main content
Calnex LogoCalnex
Math

Basic Area Calculator

Calculate areas of rectangles, squares, triangles, circles, parallelograms and trapezoids. Understand perpendicular height and the assumptions behind perimeter outputs.

Area15.00 sq unitsView results

Real-time Results

Area
15.00sq units
Perimeter
16.00units
Formula Used
A = l × w = 5 × 3

How it works

Choose one of six flat shapes and enter lengths in a single common unit. Area uses the shape’s base and perpendicular height, or its radius. The perimeter output is exact for a rectangle, square or circle; other modes make additional assumptions that are important when using a result for fencing, edging or materials.

A vertical height is not a sloping side

A triangle with base 6 and perpendicular height 4 has area 12 even if its apex moves horizontally. That move can change its other sides and perimeter while leaving its area unchanged.

When the perimeter is only an assumed model

Triangle and trapezoid modes assume an isosceles shape for perimeter. Parallelogram mode currently uses 2 × (base + height), treating height as a side; this is not the perimeter of a general slanted parallelogram. Use that mode’s area result, and obtain actual side lengths separately for a boundary calculation.

Examples and interpretation(3)

How much area does a 4.2 m by 3.5 m floor cover?

Shape
Rectangle
Length
4.2
Width
3.5
  1. Area = 4.2 × 3.5 = 14.70 m².
  2. Perimeter = 2 × (4.2 + 3.5) = 15.40 m.
Area
14.70
Perimeter
15.40

Area describes coverage; perimeter describes the boundary. This example includes no allowance for material waste or room obstructions.

Base 6 and height 4: what is known about a triangle?

Shape
Triangle
Base
6
Height
4
  1. Area = 6 × 4 / 2 = 12.
  2. For the assumed isosceles shape, each equal side is √(3² + 4²) = 5; perimeter = 16.
Area
12.00
Perimeter
16.00

The area applies to any triangle with this base and perpendicular height. The displayed perimeter requires the additional isosceles assumption.

A circle has diameter 5: which number should I enter?

Shape
Circle
Radius
2.5
  1. Radius = diameter / 2 = 2.5.
  2. Area = π × 2.5² ≈ 19.63; circumference = 2π × 2.5 ≈ 15.71.
Area
19.63
Perimeter
15.71

Entering 5 as the radius would multiply the area by four and the circumference by two.

Inputs

ParameterDefinition & Valid Bounds
ShapeSelect the geometric shape

Rectangle · Square · Triangle · Circle · Parallelogram · Trapezoid

LengthLength of the shape
WidthWidth of the shape
Side LengthLength of one side of the square
BaseBase of the triangle
HeightHeight of the shape
RadiusRadius of the circle
Top BaseLength of the top base of the trapezoid

Formula

Rectangle: A = length × width
Square: A = side²
Triangle: A = base × perpendicular height / 2
Circle: A = πr²; circumference = 2πr
Parallelogram: A = base × perpendicular height
Trapezoid: A = (base₁ + base₂) × perpendicular height / 2

How to use

  1. Select the shape before filling its dimensions.
  2. Convert every length to the same unit. Enter perpendicular height for a triangle, parallelogram or trapezoid, and radius rather than diameter for a circle.
  3. Read area in squared units. Review the perimeter assumptions before using its value as a boundary measurement.

Frequently asked questions

Why is the area unit squared?

Multiplying two lengths produces squared units. Lengths in metres give m²; centimetres give cm². Converting 1 m² requires 10,000 cm², not 100 cm².

Can this calculate an L-shaped room?

There is no arbitrary-polygon mode. Split the room into nonoverlapping rectangles, calculate each area and add them. Subtract any cutout counted inside a larger enclosing rectangle.

Is trapezoid height the sloping side?

No. It is the perpendicular distance between the two parallel bases. A sloping side cannot replace height without additional angle or side information.

Should I add 10% waste to every area?

No fixed waste allowance is applied here. The area is geometric coverage. Cutting patterns, tile sizes, packaging and site conditions determine a separate material allowance.

References

Complementary Tools

Back to MathAll Calculators
Related Tags: